Ford Escape Manuals

Ford Escape: Wipers and Washers / Washers

Washer Precautions

WARNING: If you operate your vehicle in temperatures below 41°F (5°C), use washer fluid with antifreeze protection. Failure to use washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.

Do not operate the washers when the washer reservoir is empty. This could cause the washer pump to overheat.

Keep the outside of the windshield clean. The rain sensor is very sensitive and the wipers may operate if dirt, mist or insects hit the windshield.

Using the Windshield Washer

Ford Escape. Washers

Ford Escape. Washers Pull the lever toward you to operate the windshield washer.

Note: A courtesy wipe occurs a short time after the wipers stop to clear any remaining washer fluid when switched on.

Switching the Courtesy Wipe On and Off

  1. Press Settings on the touchscreen.
  2. Press Vehicle Settings.
  3. Press Wipers.
  4. Switch Courtesy Wipe on or off.

Using the Rear Window Washer

Ford Escape. Washers

Push the lever away from you to operate the rear window washer.

Note: A courtesy wipe occurs a short time after the wipers stop to clear any remaining washer fluid when switched on.

Adding Washer Fluid

Ford Escape. Washers

    Checking the Wiper Blades. Replacing the Front Wiper Blades. Replacing the Rear Wiper Blades

    Checking the Wiper Blades Run the tip of your fingers over the edge of the blade to check for roughness. Replacing the Front Wiper Blades Lift the wiper arm and then press the wiper blade locking buttons together...

    Wipers and Washers – Troubleshooting

    Wipers and Washers – Warning Lamps Illuminates when the windshield washer fluid is low. Wipers and Washers – Frequently Asked Questions Why are there streaks and smears on the windshield? The wiper blades could be dirty, worn or damaged...

    Other information:

    Ford Escape 2020-2025 Service Manual: Disassembly - Transmission - Plug-In Hybrid Electric Vehicle (PHEV)


    Special Tool(s) / General Equipment 307-163 (T86P-70043-A) Remover, Stator Case BearingTKIT-1986-LMTKIT-1986-F 307-586Differential bearing cup removerTKIT-2006UF-FLMTKIT-2006UF-ROW 307-741Spring Compressor, F Clutch 307-821Motor Rotor Remover Installer 308-001 (T58L-101-B) Remover, Pilot Bearing Hydraulic Press Puller Punch Wooden Block ..

    Ford Escape 2020-2025 Service Manual: General Procedures - Vent Patch


    Repair   WARNING: To prevent the risk of high-voltage shock, always follow precisely all warnings and service instructions, including instructions to depower the system. The high-voltage system utilizes approximately 450 volts DC, provided through high-voltage cables to its components and modules. The high-voltage cables and wiring are identified by orange harness tape or orange wir..

    Categories

    Master Access Code

    What Is the Master Access Code

    The master access code is a factory-set five-digit entry code. You can operate the keypad with the master access code at any time. The master access code is on the owner’s wallet card in the glove box and is available from an authorized dealer.

    Displaying the Master Access Code

    To display the factory-set code in the information display:

    Ford Escape. Master Access Code

    Remove the rubber mat. Insert the first programmed key in the backup slot. Press the push button ignition switch once and wait a few seconds. Press the push button ignition switch again and remove the key. Within 10 seconds, place a second programmed intelligent access key in the backup slot and press the push button ignition switch.

    read more

    Copyright © 2025 www.fordescape4.com